Monday, April 4, 2016

How To Cut Plywood With A Circular Saw

uicok woodworking 1:03 AM

Getting accurate, straight cuts on full sheets of plywood or MDF can be an expensive proposition. The best way to do it is with a good, heavy table saw. If youre limited on space you can also use a plunge cut track saw like the Dewalt

circular saw guide will help you make accurate rip and cross cuts in full 4 x 8 sheets of plywood.
Since this circular saw cutting jig gets placed up against the cut line, it makes it much faster than other cutting guides that require you to offset the guide some distance from the line. The design also helps prevent splintering and tear out of the thin plywood veneer.

What Youll Need

Materials

4 x 8 sheet of 1/4" tempered hardboard, melamine or plywood (3/8" or 1/2" will also work)
Appropriate screws or staples depending on material
1 can of Rust Oleum AS2102 Anti-slip Spray Paint
Pencil

Step 1

Measure the distance between the edge of the circular saw base and the circular saw blade on the bottom of your circular saw as shown.

Youll be measuring the longer of the two distances. It should be the side opposite where the arbor nut is.

Write down this measurement as youll need it later.

Step 2

Lay the rigid foam insulation on the floor or on a large worktable. The insulation will serve as your cutting surface so you dont have to rig up a bunch of sacrificial boards.

Mark the factory edge of one of the 8 lengths of the hardboard with some arrows and mark a cut line 3" from that edge.

Set the depth of cut on the circular saw to just over 1/4", the thickness of the panel and cut along the line. If you dont have a way of making a perfectly straight cut dont worry, well only be using the factory edge.

Step 3

Take the circular saw fence to blade measurement you obtained in Step 1 and add the width of the previous cut (3") plus another 4-5" and mark a straight line that distance from your last cut on the hardboard panel and cut out that section. Again it doesnt have to be perfectly straight.

Step 4

Align the first piece you cut on top of the second piece. Make sure the factor edge (marked by arrows) is facing the right. On the right side of the board make sure there is at least the width of the fence measurement from Step 1 plus 1". You can use a large t-square like a drywall square to help keep the pieces aligned.

Screw or staple the top guide to the base. You can glue it in place but using screws or staples will allow you to reposition the guide if the edge starts getting torn up. Make sure the tips of the screws or staples dont poke through the bottom piece or it could scratch the wood youre trying to cut in the future.

Step 5

Place your guide over Take your circular saw and place the base tightly up against the factory edge of the top guide and carefully cut off the excess from the bottom of the guide.

You now have a circular saw guide that will allow you to rip a full length sheet of plywood. Your cut line will be where you place the edge of the guide. This makes it easy to make accurate and straight rip cuts in plywood with a circular saw.

Step 6

On the back side of the guide that will be in contact with the plywood youre cutting, spray an anti-slip spray such as Rust Oleum AS2102 Anti-slip Spray Paint

Using Your Circular Saw Guide

Using your DIY Circular saw guide is easy. You no longer need to know how far the blade cuts from the face like you do when youre cutting with other straight edges.

Lets assume we want to rip a 12" wide board out of a sheet of plywood. Simply place the plywood on top of the rigid insulation and mark a line 12" from one of the edges of the plywood.

Now place your plywood cutting jig on top of the plywood. The jig should be on the keep side of the line and the edge of the guide should be right on the line as shown. Clamp down the guide at each end to prevent it from slipping. Make sure the clamps wont get in the way of the saw.

Set your circular saw to cut just over the thickness of the plywood youre cutting plus another 1/4" (or the thickness of your guide) and carefully cut using your circular with the base pressed up against the guide.

Preventing Tear Out

Keeping the good side of the plywood face down on the rigid insulation, and keeping the depth of cut just below the plywood will help minimize tear out on the bottom of the plywood.

Since the guide is right up against the cut line, it will help prevent tearout on the "keep" side of the cut. To minimize tearout on the waste side you can first use a utility knife to score along the cut line. Placing blue painters tape along the line also helps.

The most important component to reducing tearout though is a good circular saw blade. The best circular saw blade to use for plywood is the Freud LU79R007 Perma-Shield Coated Ultimate Plywood and Melamine Saw Blade, 5/8-Inch Arbor 7-1/4-Inch

uicok

About uicok

Author Description here.. Nulla sagittis convallis. Curabitur consequat. Quisque metus enim, venenatis fermentum, mollis in, porta et, nibh. Duis vulputate elit in elit. Mauris dictum libero id justo.